Q:  Can I use your 1 gallon concentrate product to refill your SFSRC super concentrated product with the built in hose end sprayer?
A:  Not at this time.  The 1 gallon concentrate product is a different formulation and less concentrated then the SFSRC product.  You would not get the right concentration of Spray & Forget to achieve optimal performance.

Q:  Will Spray & Forget work on composite decking and/or wood such as Trex?
A:  Yes!  Spray & Forget works extremely well on all composite decking as both a cleaner and a preventative.  Simply use a garden pump sprayer and follow the directions on the label as if your were applying to any exterior surface.

Q:  How much area will one gallon of Spray & Forget cover?
A:  Using a garden pump sprayer, 3 gallons of water mixed with 1 gallon of Spray & Forget will cover approximately 700 Sq. Ft., a mixture of 5:1 will cover approximately 1000 Sq. Ft. and a mixture of 9:1 will cover approximately 2000 Sq. Ft.

Q:  How much coverage will I get when using your Super Concentrated (SFSRC-Q), 32 Ounce, integrated hose sprayer product or your 32 Ounce pre-mixed hand spray product?
A:  The super concentrate product will cover up to 600 Sq. Ft. per unit and the 32 Ounce pre mixed product will cover approximately 150 Sq. Ft.

Q:  How long will it take for roof stains to disappear using the “no rinse” application method?
A:  The stains will disappear in 6-9 months, on average, using 9 gallons water to one gallon of Spray & Forget mixture.  A stronger concentration can be used to expedite the process.  For example, a 5:1 mix will remove the stains in about 3-6 months on average.  The removal time is also dependent on rainfall and the severity of the infestation.

Q:  Will Spray and Forget remove roof moss?
A:  Yes.  Spray & Forget is very effective on roof moss.  Simply apply a 5:1 to 9:1 mixture of Spray & Forget (5 parts water to 1 part cleaner or 9 parts water to 1 part cleaner) to the affected area and the moss will be completely removed with subsequent rainfall over the next 3-6 months.  For thick moss applications, remove as much of the growth as possible first using the back end of a rake or broom and then apply Spray & Forget.  This will expedite the removal process.  Re-apply Spray & Forget every 18-24 months to prevent the stains from returning.

Q:  Will Spray & Forget work on stucco, brick, or siding?
A:  Yes, Spray & Forget actually works faster on these surfaces.  Apply a 5 gallons of water to 1 gallon of Spray & Forget mixture to these surfaces.  Green stains will disappear in 1-3 days and black stains in 1-8 weeks.  Do not rinse!  If you must have rapid results then you can rinse with a pressure washer using low to medium pressure.  We do not recommend using a pressure washer unless you are an experienced user as they can cause damage to many surfaces.  Re-apply Spray & Forget every 10-18 months, without rinsing, to prevent the stains from returning.

Q:  Can I paint, stain or seal a surface after using Spray & Forget on it?  If so, how long do I have to wait before painting/staining the surface?  Do I need to rinse the surface first?
A:  Yes, you can paint/stain surfaces after applying Spray & Forget on them.  If you are in a hurry, simply pressure wash the surface after applying the Spray & Forget to get it clean.  There will be a small residual of Spray & Forget left behind that will continue to remove and prevent any stains caused by biological growth that can not be seen by the naked eye.  You can then paint/stain/seal the surface after it dries.  With that said, you do not have to pressure wash or rinse the surface.  You can wait until the stains are removed with subsequent rainfall over time and then paint/stain/seal the surface when it is clean.

Q:  How long will Spray & Forget last?
A:  This is one of the unique advantages of Spray & Forget.  Spray & Forget has a residual effect and actually adheres to the applied surface.  In addition, Spray & Forget, unlike other cleaning methods such as pressure washing, will continue to clean microscopic mold spores that are unseen by the naked eye.  That means that the stains will be completed removed.  For these reasons, we guarantee that roof stains will not reappear for at least two years and that stains on all other surfaces will remain clean for at least 12 months.  Try getting that kind of result from pressure washing!

Q:  How often should Spray & Forget be applied?  Can it be used as a preventative?
A:  Spray & Forget is an excellent preventative!  After the initial cleaning, use a mixture of 9 gallons of water to 1 gallon of Spray & Forget every 24-36 months on roofs and every 12-18 months on all other exterior surfaces.  This will keep the stains from returning!

Q:  What should I use to apply Spray & Forget?
A:  Use a garden pump sprayer from your local hardware store to apply Spray & Forget unless you cannot get to the surface using this type of device.  In that case, you can purchase our super concentrated product that has a built in hose end sprayer that shoots up to 20 Feet or our empty custom hose end sprayer that also shoots up to 20 Feet can be used with our other products.  You cannot use any other hose end sprayer as they will not provide the correct mix ratios for use with Spray & Forget.  Contact us if neither device will work for your given application.  For roofs, always apply from the gutter edge to the rooftop as the surface will become slippery.  If rinsing the roof, rinse from the rooftop to the gutter edge.  Some pressure is required for rinsing.  DO NOT USE HIGH PRESSURE!

Q:  Can you use a Hose End Sprayer like the one at my local hardware store to apply Spray & Forget?
A:  Unfortunately, you cannot use the hose end sprayer from your local hardware store.  Those sprayers were not designed for Spray & Forget and do not draw at the right mix ratios for our product.  We recommend using a garden pump sprayer or our custom designed hose end sprayer with dial in mix ratios.

Q:  Can I use your empty Hose End Sprayer (SF Sprayer) for other cleaning and/or insecticide products?
A:  Sure!  Our sprayer can be used with most other products since the mix ratio can be varied.  However, always make sure to rinse the sprayer thoroughly before any application and consult with the chemical manufacturer of the product to be used before applying.  Some pre dilution with water may be needed before using other chemical products.  Consult the product manufacturer for instructions.

Q:  Will Spray & Forget work on rust stains?
A:  Unfortunately, Spray & Forget will not work on rust stains.  You might try a product called wood bleach that contains Oxalic Acid and a small brush.  Always consult with you local hardware store first and test on a small area.

Q:  Will Spray & Forget work on Cedar Shake roofs, tile roofs, metal roofs, painted siding, vinyl siding or wood decks/fences?
A:  Yes!  Spray & Forget will work on all of these surfaces.  Spray & Forget does not contain any harmful bleaching agents like chlorine or bleach and is not caustic like Sodium Hydroxide.   However, you should always test a small area first to make sure that your specific stain is not affected.  We have never had any problems with these surfaces but there are many types of stains and different building materials and grades of materials on the market.  Therefore, you should always test a small area just to be safe. Spray & Forget will remove any black and/or green stains caused by algae and mildew.  Spray & Forget will not return grayed wood to its original condition but will remove all black and green stains.

Q:  Will the roof algae/moss become slippery after applying Spray & Forget?
A:  Yes, our product will immediately begin removing the root structure of the algae and/or moss stains which results in the surface becoming slippery.  For roof surfaces, always apply from the gutter edge to the rooftop and rinse, if necessary, from the rooftop to the gutter edge with a low-pressure washer.  We recommend hiring a professional if you are not experienced with walking on roofs, heights or using a pressure washer.

Q:  Can I use a pressure washer to apply and rinse Spray & Forget?
A:  Yes, but consult with us first before using a pressure washer.  We can help you convert the pressure washer to a low pressure system for rinsing roofs and we can describe the best application methods.  DO NOT USE HIGH PRESSURE ON YOUR ROOF!

Q: What is the rapid result method, mixture ratio, and application technique? 
A:  Although we recommend using our “no rinse” application method since it is far safer, easier and less labor intensive, you can get rapid results using Spray & Forget.  You would apply a 5 parts water to 1 part Spray & Forget concentrate mixture to the surface to be treated.  Make sure that you apply to a dry surface with at least 24 hours before any heavy rainfall (check your weather forecast).  Wait at least 12 hours after applying Spray & Forget and rinse with a pressure washer using low to medium pressure.

Q: Will Spray & Forget work on a rubber roof?
A:  We do not have any data on the effectiveness of Spray & Forget on rubber.  Spray & forget was designed to removed biological growth stains caused by mold, mildew and algae.

Q: Can I use Spray & Forget on my tub or shower?
A:  We do not market Spray & Forget for indoor use.  Therefore, we do not have any data to confirm or deny how Spray & Forget will work on indoor surfaces.

Q: What is the coverage with a 32 Oz pre mixed?
A:  Approximately 100-150 Square Feet

Q: Will Spray & Forget work on my motor home, boat, patio furniture, awnings or convertible top?
A:  Spray & Forget works very well to remove and help prevent green and black stains caused by biological growth on these surfaces.  It works very well to remove any green algae stains without rinsing.  Black mildew stains may require some brushing or low pressure rinsing on some of these surfaces.

Q: Will Spray & Forget work in my crawl space?
A:  We do not have any data on using Spray & Forget in crawl spaces.  Spray & Forget was designed to eliminate stains caused by biological growth but requires some pressure to actually remove the biological growth where the surface is not accessible to rain fall.

Q: What if I apply Spray & Forget and it does not rain for several weeks.
A:  It is all right if you do not get rain for several weeks.  In contrast, it is NOT all right if you get rain within 24 hours after applying Spray & Forget.

Q: Does the temperature affect Spray & Forget?
A:  No, temperature does not affect Spray & Forget.  However, you should apply it when the temperature is above freezing.

Q: What is the best mixture to use for the Spray & Forget method?
A:  We recommend 5 parts water to 1 part Spray & Forget concentrate for all initial cleaning applications and 9 parts water to 1 part Spray & Forget concentrate for all preventive applications.

Q: Can I spray the surface down with water every few days to make it work quicker?
A:  We do not recommend this!  We have no data to support that this technique will expedite the removal process and it may have a negative impact.

Q: Can I use Spray & Forget on Efis and Drivit?
A:  Yes, Spray & Forget works very well on these surfaces.  You will have to use the “no rinse” application as using any pressure on these surfaces may cause damage.  For stubborn stains on highly textured surfaces, you may need to slightly brush the surface with a soft to medium bristled brush while the surface is still wet, after application, and then rinse with a garden hose or use a pressure washer with low to medium pressure.

Q: Can I use an Ortho hose end sprayer to apply Spray and Forget?
A:  No.  The Ortho sprayer will not mix at the right concentration for use with Spray & Forget.  You must use our custom hose end sprayer or any garden pump sprayer.

Q: Will the run off from Spray & Forget hurt my pets?
A:  No.  As a caution, you should put pets inside while applying Spray & Forget and wait until the initial application is dry before returning them to the treated area.  Run off after the initial application will not cause any harm to your pets.

Q:  Can Spray & Forget be used on a pool cage?  Will it harm my pool?
A:  Yes, Spray & Forget works very well on pool cages!  Make sure that the pool filter is running when you apply the Spray & Forget and use a mixture of 9 parts water to 1 part S&F concentrate.  Let the pool pump run for a few hours after the application.  S&F will not harm your pool.  You may want to check the PH of the pool a few hours after the application.
 
Q: Will Spray & Forget work on my gutters?
A:  Spray & Forget was not designed to remove black vertical streaks (Referred to as Tiger Stripes) from light colored gutters.  It will remove any green stains.

Q: Will Spray & Forget kill Artillery Mold?
A:  No. Artillery mold is extremely difficult to remove.  Artillery mold creates a protective enamel shell around itself that is nearly impossible to penetrate.  The best way to attack artillery mold is to prevent it from occurring.  Most artillery mold is transferred to your home via some form of mulch.  Make sure to test any mulch for artillery mold before putting it near your home.

Q: Can I apply Spray & Forget on exterior Marble, Granite, and/or Concrete?
A:  Sure.  Spray & Forget can be used on these surfaces.  However, it is best used as a stain preventative on flat concrete surfaces such as driveways and sidewalks.

WWW.SPRAYANDFORGET.COM
Marketed and Distributed by Spray & Forget
P.O. Box 16478
Sugar Land, Texas 77496-6478
866-641-0826 Office              832-201-7782  Fax
Email:  CustomerService@SprayandForget.com